Poultry · PO-021
Clean poultry-PPE floor cabinet
Keep clean dedicated protective clothing and supplies in a closable cabinet in a dry clean zone; not a sealed biosecurity barrier.
Editorial construction draft. Original digital diagrams; no physical build or load certification. Read dimensions, fit and use limits before making changes. US customary dimensions control; metric values are references.
Before marking and cutting
- Read every step and identify the installed orientation. Make the component off-site with birds excluded.
- Measure the actual receiving space, chosen commercial accessories and access route. Stop if the example does not fit; changing only one member can invalidate the assembly.
- Reject split, warped, moldy or chemically contaminated stock. Keep exposed mesh cut ends and all sharp fasteners inaccessible to birds.
- The drawing dimensions control; illustrations are not full-size templates. Allow a saw kerf between parts when laying out stock.
Use limits
- No person may stand or sit on this component. No tested load rating is claimed.
- A site-specific safe location and supervision are required; remove it if birds become trapped, peck damaged material, or cannot use their normal feed, water, shelter and escape routes.
Materials and cuts
| Part | Qty | Size to cut | Material |
|---|---|---|---|
| A Full-height side | 2 | 30 × 12 × 3/4 in 762 × 304.8 × 19.05 mm | Exterior-bond plywood, measured actual thickness. Square ends; remove splinters. |
| B Between-side top/bottom | 2 | 18 1/2 × 12 × 3/4 in 469.9 × 304.8 × 19.05 mm | Exterior-bond plywood, measured actual thickness. Square ends; remove splinters. |
| C Back | 1 | 20 × 30 × 1/4 in 508 × 762 × 6.35 mm | Exterior-bond plywood, measured actual thickness. Square ends; remove splinters. |
| D Fixed shelf | 1 | 18 1/2 × 12 × 3/4 in 469.9 × 304.8 × 19.05 mm | Exterior-bond plywood, measured actual thickness. Square ends; remove splinters. |
| E Overlay door | 1 | 29 3/4 × 19 3/4 × 1/2 in 755.65 × 501.65 × 12.7 mm | Exterior-bond plywood, measured actual thickness. Square ends; remove splinters. |
Hardware and consumables
- 24 × #8 corrosion-resistant exterior wood screw 2 in (50.8 mm). Carcass and shelf [N1]
- 14 × #8 corrosion-resistant exterior wood screw 1 in (25.4 mm). Back [N1]
- 3 × Overlay cabinet hinge with compatible short hardware. Select for 1/2 in leaf and actual overlay; follow maker instructions
- 1 × Pull and positive cabinet latch. Smooth-ended hardware only
- 2 × Substrate-appropriate anti-tip retainer. Cabinet remains floor-supported
- N1 applies to every entry marked [N1]: Use compatible coatings/metals and the maker's pilot-hole guidance; do not substitute drywall screws.
Tools
- Tape measure, square and pencil
- Saw appropriate to material and work supports
- Drill/driver, countersink and pilot bits selected for the screws
- Clamps, sanding block and eye/hearing protection; dust control appropriate to the material
Assembly
- Select a dry clean-side floor location, separated from chemical products and dirty boots. This wood cabinet is not waterproof, rodent-proof or suitable for sterilizing supplies.
- Cut A sides to 30 × 12 in, B top/bottom and D shelf to 18 1/2 × 12 in (469.9 × 304.8 mm), all actual 3/4 in plywood.
- Cut C back to 20 × 30 in from actual 1/4 in ply and E door to 29 3/4 × 19 3/4 in (755.7 × 501.7 mm) from actual 1/2 in ply.
- Clamp B between A with bottom B at z = 0 and top B at z = 29 1/4 in. The carcass outside width is 20 in (508 mm).
- Attach each B edge through A with four 2 in screws per joint, sixteen total, keeping the first/last holes 1 in from the front/rear.
- Mark D's underside at z = 14 5/8 in (371.5 mm) and clamp it level between A. Use four 2 in screws through each side into D.
- Square the carcass and attach C on the rear with fourteen 1 in screws, centered on the shell edges and kept clear of the planned anti-tip fixings.
- Sand and fully cure a suitable optional coating before putting clean clothing inside. Do not line shelves with loose absorbent paper that hides dampness.
- Fit E centered over the front, leaving a 1/8 in (3.2 mm) outer reveal. Use three manufacturer-selected overlay hinges compatible with the actual panel thickness; follow their hole pattern and short-fastener limits.
- Fit a low-profile pull and positive latch with smooth-ended hardware. The closed door must not rub the floor or require the cabinet to be pulled forward.
- Set on a level dry floor and install two suitable upper anti-tip retainers to inspected backing; keep the cabinet floor-supported rather than treating these as hanging anchors.
- Store only clean dry supplies, close the door after use and check regularly for dampness, pests or contamination. Replace affected supplies; the cabinet does not disinfect its contents.
Checks
- Between-side parts are 18 1/2 in wide; outside width 20 in. Shelf underside is 14 5/8 in.
- Door is 1/4 in smaller than the carcass in both width and height, centered to give 1/8 in outer reveal.
- Cabinet is level, floor-supported and retained against tip; actual hinge installation does not expose sharp points.
- Door latches easily and clean supplies stay separate from dirty equipment and chemicals.
Cleaning and maintenance
- Inspect before each use for splits, loose joints, protruding points and trapped debris.
- Remove accumulated litter or manure promptly. When cleaning is needed, move birds away, remove debris first, wash and use only a suitable label-directed product if disinfection is indicated; let the item dry before return.
- Recheck the fit after seasonal wood movement. Replace cracked panels, rusted fasteners or frayed liners instead of concealing damage.
- Sand accessible edges to a small smooth radius. Use a removable washable contact liner where specified. Any optional coating must be suitable for the intended animal-equipment use and fully cured according to its label before installation. Porous wood is not represented as a disinfectable food-contact surface.
Primary context
These sources inform the context and do not endorse the original construction design.